Joint Sealants

By:Deepak Kanitkar
DGM – Technology & Business Development
Chembond Chemicals Limited, Mumbai.

One of the most essential materials for making the Building Envelope waterproof is the joint sealant. Joints are there invariably in all civil constructions. According to material of construction, there are different kinds of joints. Some are only for joining, some are for accommodating the movements. Movements are mainly because of thermal gradients caused by temperature variations. There are also movements due to seismic activity, settlement, shrinkage, creep and dynamic loads, temperature variations due to processes etc.

All joints which are formed due to above reasons must be properly sealed, monitored and maintained. This is essential to protect the structures from ingress of foreign matter such as dirt, dust, water, chemicals and organisms. Depending on the requirement of each joint there are various types of sealing solution available in the market.

Here we will discuss some very commonly used joint sealants in civil construction. There are mainly two types Viz. Liquid applied and Pre-Formed. Varieties of polymers are used to manufacture liquid applied joint sealants. These include Polysulfide, Polyurethane, modified Polyurethanes, Silyl Terminated Polyether’s, SPURs, Polymer modified Bitumen, Flexible Epoxy, Silicones and butyl rubber based materials are now being used.

Joints in Concrete

There are different types of joints in concrete. As there is always a shrinkage involved while using Cement Concrete, this factor must be considered while concrete placement. Concrete cannot poured in thick sections or longer spans, for two reasons. First reason is the heat generated in the concrete due to hydration of cement, which causes differential thermal gradient between the core and the surface. As the mass increases this gradient also increases. As per standard practices, this gradient shall be as close as or less than 20oC. This limits the placement volume. Other reason is that, most of the times continuous pours are not possible or placement may get interrupted due to unavoidable delays. Apart from this, longer and wider sections may crack due to drying, chemical, autogenous shrinkage, creep or thermal expansion and contractions. Expansion Joints, Control or Contraction Joints, Isolation Joints and Detailing joints are some of the type of joints in buildings.

Expansion Joints are provided to allow movement in a structure caused by thermal or other factors such as wind loading.

Control joints are provided for expected cracking due to factors such as settlement, drying shrinkage or separation in building materials after construction. Internal control joints are typically nonmoving while in the exterior they also accommodate movement. External Control joints require more design work.

Isolation joints are placed at junctures where changes in material require isolation for any differential movement between two different materials. Typical example is window frame perimeter abutting façade materials.

Detailing joints are designed as a part of waterproofing system. They are vital to impart water tightness at structure details such as pipe penetrations and changes in planes prior to application of primary waterproofing compounds.

There are some thumb or basic rules for design of joints which are:

  1. Joint size no smaller than 6 mm.
  2. Generally limit the joint size in buildings to 25 mm
  3. Joint opening shall be kept at a minimum of four times anticipated movement.

Sealant design shall take following rules in consideration while deciding width and depth.

  1. Minimum material thickness shall be 6 mm.
  2. Up to 12mm wide joints shall have Depth (D) = Width (W)
  3. Wider joints and traffic joints shall have D = W/2.
  4. Three-way adhesions is not allowed so use of backer Rod or Bond breaker tape is a must.
  5. While using PE closed foam backer rod, it shall be 25% more in diameter than the joint size.
  6. Porous surfaces generally require primer to avoid passage of air/impurities to sealant in wet stage and for proper adhesion.

In liquid applied sealants, there are mainly two types, viz. single component and two components. PU based sealants such as KEM JOINT PU 100 work on a principle of curing by reaction with atmospheric moisture. Polysulfide based sealants such as KEM Joint GG and KEM Joint PG, have two component system. These cure because of chemical reaction between the hardener and base components.

Following illustrations provide an insight into application and mixing methods.

Joint Sealanta Joint Sealanta
Use of Bond breaker tapes to avoid three way adhesion of Sealant A section of joint showing sealant placed over a PE closed cell foam backer Rod.
Joint Sealanta Joint Sealanta
Taping of Joint with masking tape to ensure Neatness Sealant Gun for application of Gun Grade sealant
Joint Sealanta Joint Sealanta
Filling of 2 part sealant in application Gun using follower plate
Advertisements

About CPWD Engineers' Association

It is a great pleasure to inform you that CPWD Engineers Association has launched its Blogging page. Now this page will bring to you latest developments/activities of our Members. All efforts are being made to ensure that this website caters to the requirement of CPWD Engineers so far as their various information through this Association is concerned. In course of time this page would be the most useful source of information and would reduce the gap between the Engineers and this Association. Please must inform to other members too. This page is added for various interesting things, Important News & Activities of Association .

Posted on Thu, May 3rd, 2012, in What's new and tagged , , , , , . Bookmark the permalink. 1 Comment.

  1. Thanks for sharing the information about expansion joints and other joints and how can we avoid the corrosion.

Please post your feedback/comments

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: